P-Traps can be found at almost any fixture that drains water and are designed to prevent hazardous sewer gases from entering the building. A P-Trap is comprised of a curved “trap” called a J-Bend and a drain pipe called a Wall Bend. The Tailpiece on the Lavatory Drain fits into the P-Trap J-Bend, connecting to the Wall Bend, which then enters the wall. They are available with or without cleanout plugs. If one with a cleanout plug is installed it can be cleaned without removing and installing a new trap.
S-Traps are also used to prevent hazardous sewer gases from entering buildings, and are designed to drain into plumbing below the floor for installations where there is no access to plumbing directly behind the wall.
Because of their shape, J-Bends retain a small amount of water after the fixture’s use. This water in the trap creates a seal that prevents sewer gas from passing from the drain pipes back into the occupied space of a building or home.
Vanity Traps are P-Traps which feature an extra-long (15”) Wall Bend to accommodate deeper Vanity installations.
“OS&B® Traps are warranted for 5 years, from date of purchase, against workmanship and/or material defects. Buy Quality. Buy OS&B® Traps for your next plumbing project.”
Tubular P-Traps
Cast P-Traps
Vanity Traps 15” Wall Bend
S-Traps
Repair Traps
Decorative T-Traps
J-Bends
Sink Traps-Cast Elbow
With trend setting innovations like our Clicker® Closure mechanism and our Daisy™ Grid Drain, OS&B® has set a new standard in Lavatory (Lav) Drain technology. OS&B® has all of your Lav Drain needs covered with a complete selection available in a variety of materials, configurations, sizes and finishes.
Clicker®
Mechanical Pop-up
Open Grid
Hooded Dome
Plug & Chain
Wheelchair Accessible
1-1/2” Tubular Traps
Continuous Wastes
Continuous Waste Arms
Extension Tubes
Sink Tailpieces
Flanged (T.O.E.) Tailpieces
Dishwasher Tailpieces
1-1/2” Plastic Repair Connectors
1-1/2” Dishwasher Bushings
Urinal Tailpieces
Threaded Tubes
Double Slip Repair Connectors
Waste Connectors
Cable-Drive®
Lift & Turn
Parts
Push-Pull
Tip-Toe
Trim Kits
Twirl™
Bath Tub Drain Trim Update Kits
Testable Rough-ins
Integral Tub Drains
360 Fill&Drain™
Trip Lever
Braided FLEX
Side Discharge Shower Drains
Shower Drains for Molded Bases
Testable Shower Drains for Preformed Shower Bases
Shower Pan Drains
Floor Drains
Wood Deck Drains
The patented Island Tub Drain® Freestanding Tub Rough-In – A revolutionary product minimizing the time and effort required to install a freestanding bath. Island Tub Drain® allows the DWV system to be pre-plumbed before making the connection between bath drain and the p-trap. This means no access panels required below the fixture! Island Tub Drain® contains a positive action seal against the supplied tailpiece connection kit and is compatible with virtually all tubs. The bath drain connection is now accessible by simply lifting the bath. In addition, the asymmetrical deck plate is designed not to interfere with the floor mounted tub filler rough-in. Island Tub Drain® is testable for new construction.
1 Piece Island Tub Drains
2 Piece Island Tub Drains
Automatic Plumbing Vent
Sump Pump Check Valves
Air Admittance Valves
Duplex Strainers
Bead Chains & Couplings
Nuts
Escutcheons/Flanges
Rings & Washers
Trap Seal Primers - Hose Barbs
W/C Closet Bolt Nuts - Open Head
W/C Closet Washers
W/C Premium Closet Bolts
W/C Closet Bolts
W/C Toilet Flange Extension Kits
Mainline Backwater Valves
Non-Testable Rough-ins
Island Tub Drain
Shower
Rough-ins
